In this video I demonstrate how to perform a turbocharger replacement on a 2019 Veloster N. I remove the Veloster N turbo and install a new OEM Elantra N turbo. The installation is done from the top of the engine without lifting or removing the lower subframe or the entire engine. Since my wife and I recently blew the turbocharger on her Veloster N, there are additional steps outlined in this video due to the way her turbo blew.

This was a big project and the video is long and contains a lot of content. I apologize if I get the size of a nut or bolt wrong in the video. I tried to remember the size of all the nuts and bolts but I may slip up in the video. Just know that 10mm, 12mm and 14mm are the three most common sizes you will encounter during this process. I also posted a link to the shop manual with all the torque specifications for each bolt. I tried to cover the most important bolts in the video.

The torque specifications can be found in the PDF document “Mechanical Motor Systems”.
https://drive.google.com/drive/folders/1zBshNcI9d9RWw6r9EoOw31fPertTKu-M

If I missed something or you have any questions, feel free to ask. I read all comments and emails and try to respond as quickly as possible. If you message me directly, sometimes I don't see it, so comments or emails are best.

Veloster Downpipe Removal/Installation Video – https://youtu.be/ZZxWAH3wh_M
Video about changing the oil in the Veloster – https://youtu.be/SjcZIfF7Wao
Veloster High Pressure Fuel Pump Video – https://youtu.be/Ex37e65zlS8
Veloster intercooler removal/installation video – https://youtu.be/oF7CQUgs3TM
Veloster Intake Removal/Installation Video – https://youtu.be/TZcZ0UxWNoE

N75 Motorsports ELANTRA N TURBOCHARGER UPGRADE FOR VELOSTER N (WITH HOT PIPE CONVERSION AND TURBO COVER)
(You must select ARP downspout bolts from the drop down menu.)
https://n75motorsports.ca/collections/veloster-n/products/elantra-n-turbocharger-upgrade-for-veloster-n?variant42149227299002

In the video I try to answer the following questions.
1. How do I remove a 2019 Hyundai Veloster N-Turbo?
2. How do I install a 2022 Elantra N-Turbo into a 2019 Veloster N?
3. How do I replace the turbo on a Hyundai Veloster N without a lift?
4. How do I remove a Hyundai Veloster turbo (2019) from the top of the engine?
5. How do I remove a valve cover from a 2019 Hyundai Veloster N?
6. What do you need to install a new turbo in a 2019 Hyundai Veloster N?

OEM parts used
Exhaust manifold gasket (should be included in the turbo kit)
Turbo water pipe banjo bolt crush washers (2)
Crush washers for banjo bolts of turbo oil supply line (2)
Crush washers for banjo bolts of turbo coolant line (2)
Turbo oil return line seal
Valve cover gasket
Valve cover HPFP gasket

Tools required
Car ramps/car jacks
Socket wrench insert, metric: 7 mm, 10 mm, 12 mm (12-point), 14 mm, 17 mm, 18 mm, 19 mm
Ratchet wrench with flexible head
Short pliers/Long pliers
Coolant drip pan or bucket/oil drip pan
Coolant 1 gallon
Oil 5qts/Oil filter

Tools used in the video
1. Low Profile Jack 1.5 Ton (3,000 lbs.) – https://amzn.to/3WoBWZs
2. Car ramps 6.5/" lift – https://amzn.to/3LAtdPd
3. 1/2" impact wrench – https://amzn.to/4buCZ0G
4. Needle nose pliers – https://amzn.to/3IOq0L7
5. WD-40 Specialist Penetrant with flexible straw – https://amzn.to/3Vec9Ei
6. Trim Removal Tool Kit – https://amzn.to/3k9pG00
7. Ratchet wrench set – https://amzn.to/3WktMl4
8. Craftsman Socket Set – https://amzn.to/3ixW4sD
9. O2 sensor removal socket – https://amzn.to/3UWpTT2
10. 1/2" wheel socket set – 15/17/19/21/22mm – https://amzn.to/3on5rOS
11. 1/2-inch torque wrench 10-150 ft./lb. – https://amzn.to/3WqcW44
12. Swivel socket wrench set – https://amzn.to/3ShCC1W
13. Impact Resistant Socket Adapter Set – https://amzn.to/3Wz9iq5
13. Leak-proof coolant funnel set – https://amzn.to/3Wzo3Jx
14. Hyundai Oil Filter 26300-35504 – https://amzn.to/3Wzg3Z2
15. WIX 51334XP Oil Filter – https://amzn.to/3SkhxUL
16. Motul 109776 8100 X-Cess Gen2 5W-40 Engine Oil – https://amzn.to/3Sm9Ugi
17. Lisle 63600 Oil Filter Tool – https://amzn.to/3LDmTGG
18. Permatex 82180 Ultra Black Gasket Maker – https://amzn.to/4foSNEq

Disclaimer:
This is not a paid advertisement.

This channel participates in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com.

Music Apple iMovie – Flashbulb by Hapasan

Feel free to leave a comment or send me an email to [mail protected]

Please like, share and subscribe for more content! Thanks

#hyundai #velostern #n75motorsports #elantran #blownturbo #turbofailure #turboswap #elantranturbo #velosternturbo #enturboswap #vnturboswap

Please take the opportunity to connect with your friends and family and share this video with them if you find it useful.